最新升級版對刀機DT02，對刀精度1微米
維宏接收器適用於維宏系統
一.應用 Application
低功耗無線對刀機,實用於各種CNC加工中心.
low-power wireless tool setting gaguge, applications operating in all kinds of machine cnc center.
二． 操作使用步驟說明 Operation Instruction
1．將接收器連接到系統，如下說明：（接收器）Connect the receiver to the cnc system
說明：description
1、K2為內部繼電器輸出的2個腳，平時K2處於斷開狀態，當對刀觸發的時候，K2閉合。
K2 is the electric relay output normal open switch,which will be closed when the probe signal is triggered.
2、給接收器供電：接收器支持5V電壓輸入。
當接收器有電壓輸入後，接收器開始工作，接收器的工作指示燈閃爍。
Power on the receiver.please make sure that the input power is 5v-36v DC. The work led flash to indicate power on ok.
3、給對刀器安裝上2節AAA電池。
3、給對刀器安裝上2節AAA電池。
拆開對刀器底蓋------安裝上2節AAA電池（註意電池正負方向）------裝上對刀器底蓋
Install the two AAA batteries to the terminal device.
Open the the battery door->install the 2 AAA.(Attention to The battery positive and negative direction )->close the battery door.
4、輕壓下對刀機，對刀指示燈亮；同時無線連接指示燈亮；對刀機將對刀信號無線傳遞給接收器，接收器對刀指示燈亮，對刀開關處於閉合狀態；完成對刀。
4、輕壓下對刀機，對刀指示燈亮；同時無線連接指示燈亮；對刀機將對刀信號無線傳遞給接收器，接收器對刀指示燈亮，對刀開關處於閉合狀態；完成對刀。
To Touch the bulge of the tool setting gauge device until the probe led and the RF Led light. the probe signal will be transferred to the receiver,the receiver will trigger the probe switch to close.
![]()
三、電氣參數 Electrical specifications
3．1：接收器（The receiver）
．工作電壓：支持寬電壓輸入：直流：5V
Work voltage:5v~36 DC
．工作電流：平均電流小於：20Ma
Current consumption: type 20ma
．無線使用距離：20米
Wireless distance:20 meter
．內部繼電器輸出：支持250V/50mA負載;常開型;對刀觸發,繼電器閉合.
．內部繼電器輸出：支持250V/50mA負載;常開型;對刀觸發,繼電器閉合.
The relay normal open contacts output: support maximum 250V/50ma load.
3．2：對刀器（The tool setting gauge）
．工作電壓：2節AAA電池，直流2.4V到3.6V
Work voltage:2 AAA batteries,2.4V~3.6V DC
．工作電流：平均電流小於20uA；2節AAA電池能正常使用6個月
Current consumption: type 20uA.To work continuously more than 6 months
．無線使用距離：20米
Wireless distance:20 meter
．對刀重復精確度：0.01毫米
Probe precision:0.01mm
低壓警告：當對刀器電池電壓低於2.4V，提示更換電池。
Low power warning:please exchange the batteries when low power led light
新手教學
批發市場僅提供代購諮詢服務，商品內容為廠商自行維護，若有發現不實、不合適或不正確內容，再請告知我們，查實即會請廠商修改或立即下架，謝謝。
