廠傢供應電池容量檢測機器（12V，24V，36V，48V，64V放電機）_通訊檢測儀器_專用儀器儀表_儀器、儀表_貨源

名稱：電池容量檢測機器（64V放電機）

H—2016智能電池容量測試機使用說明書

一、本機器采用微電腦技術、PID自動控製、恒流放電，放電電流為0．5~10A可調（恒流），放電時間自動記錄、保存，電流、總電壓、單隻電壓﹑時間顯示，能精確測定電池的容量。可檢測標稱12V，24V，36V，48V,64V的電池組。終止電壓：10.5V，21V，31.5V，42V，56V,自動判別電池組電壓。是鉛酸電池生產，檢測，維修以及售後處理的必備工具。

二、相關標準：

1，根據國標在25℃環境溫度下，以兩小時率來測試電池容量，即7AH的電池以7/2=3.5A的電流放電，10AH電池的電池以10/2=5A的電流放電，依次類推。一般的新電池能達到120分鐘以上的放電時間。

2，電池容量計算公式：{放電時間T（分）÷60×放電電流I（A）}AH。

三：操作步驟：

1，插好並擰緊正極夾頭、負極夾頭和采樣線夾頭.

2，插上電源（AC220V），”嘀”一聲電源指示燈亮。

3，按“設定”鍵，默認值為5A，按“▲▼”鍵調節所需要的電流。（0.5-10A）

4,電池組串聯好,電池之間用1.5平方以上的電線連接,電線要求盡量短;串聯好的電池的編號由負極到正極依次為①號②號③號④號.

5,分電壓夾頭連接方法;1號電池正極,2號電池正極,3號電池正極,各接一根,(采樣黃線)不分序號,自動設別.

6，按“放/停”鍵即開始放電，放電結束，保存放電時間,顯示每隻電池電壓。

7,當放電過程中按一下“設定”鍵,顯示當前各單電壓及總電壓,再按返回原來狀態.

8,機器放電過程中不能設定電流值,隻能在放電之前先設定好電流值放電.

9,本機器帶充電介面,放電完成自動充電,充電器自配.

四、隨機配件:

1~正極線夾1根.

2~負極線夾1根.

3~采樣線夾1根.

4~電源線1根.

5~說明書1份.

五﹑主要參數:

1,電源～220V 50∕60HZ

2,放電電池組:12V、24V、36V、48V、64V

3,放電電流:0.5A～10A可調

4,放電電流精度:2‰

5,外觀尺寸:20㎝×15㎝×28㎝.

6,重量:3.6㎏

六、註意事項：

1，保持通風，風扇不轉時應及時維修。

2，若按“設定”鍵無反應時，請關掉電源，重新開始。

3，如按“放/停”鍵沒有反應時，請檢查極性有沒接反，或電池組一點電量也沒有.

電話：0572—6416628

傳真:0572-2954021

長興海海電子有限公司

地址：浙江省長興縣光明路288號

網址:WWW.CXHHDZ.CN

H - 2016intelligent battery capacity tester instructions

A, this instrument adopts microcomputer technology, PID automatic control, constant exile electricity, discharge current for 0.5 ~ 10A adjustable (constant-current), discharge time automatic recording, preservation, current, total voltage, single only voltage, time to show, can accurate determination of your battery capacity. Can detect the nominal 12V, 24V 36V, volt, 64V, the battery pack. Termination voltage: 10.5 V, 21V, 31.5 V, 42V, 56V, automatic discriminant battery voltage. Is lead-acid battery production, testing and maintenance and after-sales processing of necessary tools.

Second, the related standard:

1, according to gb in 25℃environmental temperature in 2 hours, rate to test battery capacity, namely 7AH battery to 7/2 = 3.5 A discharge current, 10AH batteries battery to 10/2 = 5A of discharge current, ordinal analogy. General new battery can reach more than 120 minutes of discharge time.

2, battery capacity calculation formula: {discharge time T (points) voting 60 x discharge current I (A)} AH.

Three: operation steps:

1, insert and screw down the positive chuck and anode chuck and sample line chuck.

2, plug (AC220V), "di" 1 power indicator.

3, press "set" button, the default value of 10, press "▲▼" button to adjust needed current. (0.5-10A)

4, battery, the battery is used between series more than 1.5 square wire connection, wire requirements as far as possible short, Tandem good battery anode to positive in turn by the Numbers as (1), (2), (3), (4) number.

5, divide voltage chuck connection method, 1 the battery anode, 2 battery anode 3 battery anode, each connect a root, (sampling yellow line) regardless of serial number, automatic set don't.

6, press "put/stop" button, it will begin to discharge end of discharging, save discharge time, showing every only battery voltage.

7 and when discharging process click "setup" button to display the current each single voltage and total voltage, and press return to its original shape.

8, instrument discharge process cannot set current only at discharge before setting good result discharge.

9. The instrument with charging interface, complete discharge automatically charges, charger the mixed.

Four, random accessories:

1 ~ positive wire clip 1 root.

2 ~ anode wire clip 1 root.

3 ~ sampling wire clip 1 root.

4 ~ the power cord 1 root.

5 ~ 1 portion of the specification.

Five, main parameters:

1, power ~ 50/220V 60HZ

2, discharge battery pack: 12V, 24V, 36V, volt, 64V

3, discharge current: 0.5 A ~ 10A adjustable