成份 Composition

環氧樹脂：Epoxy resin

外觀 Appearance

紅色糊狀： Paste/red-colored

比重 Specific gravity

1.28

粘度 Viscosity at 25℃,5rpm

380Pa·S(380.000 cps)

搖變性指數 Thixotropy index

6.3(1rpm/10rpm)

玻璃化溫度：glass transition temperature

85℃

接著強度Adhesive Strength 2125C

Mini-mold tr

SOP·IC 16P

44N(4.5kgf)0.2mgr twin

45N(4.6kgf)0.3mgr twin

92N(9.4kgf)0.8mgf single×2

電氣特性 Electric Property

體積阻抗係數 Volume resistance

絕緣阻Insulation resistance

初期值 Initial value

處理後* After treating*

介電常數 Dielectric constant

介電正接 Dielectric loss tangent

3.6×1016Ω·cm JIS K6911

1.2×1014Ω JIS Z3197

1.2×1012Ω

3.12/1MHZ JIS K6911

0.012/1MHZ JIS K6911

保存條件Preservation condition

2℃-5℃的冰箱保存

To be strictly kept in refrigerator from 2℃to 5℃

包裝方式

Package styles

容量

Contents

包裝單位

Pack.Unit

點膠機設備廠商

Applicable Dispenser Makers

1．條裝 Tube

200gr

10Pcs.

2．圓柱筒

300ml

5Pcs.

For our filling machines only

3．圓柱筒

350gr

12Pcs

4．罐裝PLASTIC JAR

350gr

12Pcs

5．罐裝PLASTIC JAR

1000gr

6Pcs

For screen printing

1．容許低溫度硬化。

2．儘管超高速塗敷、微少量塗敷仍可保持沒有拉絲，塌陷的穩定形狀。

3．對於各種表面粘著零件，可獲得安定的接著強度。

4．儲存安定性優良。

5．具有高度耐熱性和優良的電氣特性。

6．可用於網版印刷。

○Recommended curing condition:Over 120 sec after PCB’s surface temperature has reached 150℃.or over 150 sec after PCB’s surface temperature has reached 120℃.

○When the higher curing temperature and the longer curing time,the stronger adhesive strength can obtained.We would suggest you to search out an optimum curing condition,for the temperature exerterd on the adhesive may occasionally vary according to the size,material,etc.of component parts mounted on PCBs.

固化條件

○建議固化條件是PCB板表面溫度達到150℃後120秒以上，或者是達到120℃後150秒以上。

○固化溫度越高，且固化時間越長，可獲得更高的粘接強度，依PCB板上裝著元件材質、大小不同而實際附加於接著劑的溫度會有所不同，因此請依據實際生產情況找出最適合的固化條件。

○Adhesive should be preserved in refrigerator(below 2-5℃)to keep on its quality.

○Before processing,the adhesive should be taken out from the refrigerator for de-freezing about a few hours until it reaching the room temperature.

○The bottom of printing screen should be cleaned timely for good printing shape.

○Toluene or ethyl acetate is possible to use for cleaning up this adhesive.

使用方法

○為使接著劑的特性發揮最大效果，請務必放置於冰箱（2-5℃）保存。

室溫23℃可保存6-8小時。

○使用前請務必提前2-4小時從冰箱取出，待紅膠恢復至室溫後使用。

○為獲得良好印刷成形，請及時清潔鋼網底部。

○對紅膠的洗滌可使用甲苯，醋酸乙酯。

160

140

120

100

80

60

40

120℃/150sec

150℃/120sec

○Warranty:6Months.

○Store adhesive in a refrigerator keeping the temperature at 2-5℃

○This product may cause skin irritation to sensitive personnel.

○In case Seal-glo WT-960 gets in touch with skin,wash it thoroughly with soap and water.

○In case of eye contact,wash out with clean water and consult a medical doctor immediately.

○保證期：6個月。

○請務必將本品保存在2-5℃的冰箱內。

○如果有過敏性體質的人，直接接觸皮膚有時會引起皮膚過敏，因此請注意。

○誤沾皮膚時，請立即用肥皂水清洗。

○進入眼睛時，請盡速以清水沖冼乾淨，立即接受醫生的診察。