一、產品概述
本裝置又稱導線受損程度試驗裝置，符合GB2099.1-2008第12.2.5條款及12.3.10條款及圖11、IEC884圖11、GB1314.3等標準要求，主要用於判斷螺紋夾緊型的接線端子在設計和結構上是否達到瞭在其夾緊導線時無過度損壞導線的要求，還用於考查無螺紋接線端子是否經受得住正常使用時出現的機構應力。使用時可先預置試驗次數，到設定值會自動停機，並伴有聲音報警信號。
二、技術參數
1、工作電源：AC 220V 50HZ
2、工作速度：10±2轉/分
3、計數范圍：0～9999，默認150次（15min）
4、荷重砝碼：300g、400g、700g、900g、1400g、2000g各一個（可定制）
6、旋轉直徑：75mm
7、線套孔徑分別為：6.5、9.5、13、14.5mm（可定制）
7、高度距離：260、280、300、320mm
8、外形尺寸：350mmX570mmX960mm
9、導線、線套、高度及砝碼選配參數表
導線橫截麵積mm² | 套管孔的直徑mm | 高度mm | 與導線對應的重物kg |
0.5 | 6.5 | 260 | 0.3 |
0.75 | 6.5 | 260 | 0.4 |
1.0 | 6.5 | 260 | 0.4 |
1.5 | 6.5 | 260 | 0.4 |
2.5 | 9.5 | 280 | 0.7 |
4.0 | 9.5 | 280 | 0.9 |
6.0 | 9.5 | 280 | 1.4 |
10.0 | 9.5 | 280 | 2.0 |
16.0 | 13.0 | 300 | 2.9 |
25.0 | 13.0 | 300 | 4.5 |
35 | 14.5 | 320 | 6.8 |
1、 高度H的公差：±15mm。 2、 如果套管孔的直徑太小，不足以容納沒有緊束的導線，可以改用尺碼大一號的套管孔。 | |||
Clamping Device Test MachineCL-1
Products Information
Product details:Model CL-1
Application
Terminals with screw clamping shall be so designed and constructed that they clamp the conductor(s) without undue damage to the conductor(s).
Compliance is apparatus of checking damage .
The terminal is placed in the test apparatus according to tester and fitted with rigid, solid, stranded and/or flexible conductor(s), according to standard first with the smallest and then with the largest nominal cross-sectional area, the clamping screw(s) or nut(s) being tightened with the torque according to standard.
The length of the test conductor shall be 75 mm longer than the height (H) specified in standard.
The end of the conductor is passed through an appropriate bushing in a plate positioned at a height (H) below the equipment, as given in standard. The bushing is positioned in a horizontal plane such that its centre line describes a circle of 75 mm diameter, concentric with the centre of the clamping unit in the horizontal plane; the platen is then rotated at a rate of (10 ± 2) r/min.
The distance between the mouth of the clamping unit and the upper surface of the bushing shall be within ±15 mm of the height specified in standard. The bushing may be lubricated to prevent binding, twisting, or rotation of the insulated conductor.
A mass as specified in standard is suspended from the end of the conductor. The duration of the test is approximately 15 min.
During the test, the conductor shall neither slip out of the clamping unit nor break near the clamping unit, nor shall the conductor be damaged in such a way as to render it unfit for further use.
Power Supply: 220V 50Hz or 115V 60Hz
No.of Test: 1~9999
Rate of Testing: (10±2)r/min
Weight: 300g/400g/700g/900g/1400g/2000g*1
Diameter of gyration:75mm
Diameter of bushing hole (mm): 6.5,9.5,13,14.5
Height(H)(mm): 260,280,300,320
Conforms to standard: IEC60884Figure11,VDE0620,IEC60947.1 Figure 1
批發市場僅提供代購諮詢服務，商品內容為廠商自行維護，若有發現不實、不合適或不正確內容，再請告知我們，查實即會請廠商修改或立即下架，謝謝。
