商品代碼:3552142

  • 現在位置: 首頁 » 貨源 » 電子元器件 » 光電器件 » 激光器 »
    供應單膜激光器/激光管/激光雕刻專業激光器/光斑細激光器
    商品代碼: 3552142
    (可點擊以下立即詢價直接線上諮詢,或來電提供此商品代碼諮詢)
    即日起提供日本樂天代購服務-詳見 Rakuten-suki日本樂天代購,謝謝。
    商品詳細說明

    技術參數  

     

    型號

    KY-45S(C)

    KY-60 S(C)

    KY-60

    KY-80A/L

    KY-80B

    長度mm

    1250

    1650

    外徑mm

    Ф65(80)

    標稱功率w

    45

    60

    90

    最大連續輸出功率w

    4555

    5575

    6275

    85100

    92100

    功率不穩定度

    ≤±5 %

    光斑模式

    M21.2

    低階模

    光斑尺寸mm

    4.0±0.3

    5.5±0.3

    6.5±0.3

    光束發散角

    ≤4mrad

    ≤3mrad

    最佳工作電流mA

    18

    22

    24

     

     

    型號

    KY-100

    KY-120

    KY-130

    KY-150

    長度mm

    1650

    外徑mm

    Ф80

    標稱功率w

    100

    120

    130

    150

    最大連續輸出功率w

    105120

    125135

    135145

    145165

    功率不穩定度

    ≤±5 %

    光斑模式

    低階模

    光斑尺寸mm

    7.5±0.3

    8.0±0.3

    8.5±0.3

    光束發散角

    ≤3mrad

    最佳工作電流mA

    26

    32

    38

    42

     

    型號:KY-45SC(詳細參數

     

    特點:模式好,適用於工藝禮品打標及高精度雕刻和精細切割。

     

    產品圖

     

     

    一、安全須知(詳見KY系列激光器使用手冊)

    1光學安全須知

    激光輻射會對眼睛和皮膚造成嚴重傷害,嚴禁眼睛和皮膚直接暴露在激光輻射下!

    2電力安全須知

    嚴禁在接通高壓電源之後靠近接觸電源、激光器兩端以及它們之間相連的電線!

    3其他安全須知

    (1)本產品的激光易點燃被輻射到的易燃物品,所以嚴禁在輻射范圍內放置無關易燃易爆危險品,在工作間要準備消防設備;

    (2)使用本產品時,待加工對象在加工過程中可能產生的有害物質需要妥善處理,要保持室內的通風良好;

    (3)在激光器工作過程中始終要有人員留守,在發生異常狀況時要首先切斷所有電源;

    (4)本產品為玻璃管激光器,屬於易碎品,請輕拿輕放。

    二、安裝須知(詳見KY系列激光器使用手冊)

    1激光輻射會對眼睛和皮膚造成嚴重傷害,嚴禁眼睛和皮膚直接暴露在激光輻射下!

    2嚴禁在接通高壓電源之後靠近接觸電源,激光器兩端以及它們之間相連的電線!

    3一定要確保“中段出水口”朝上。

    4隻有確保冷卻水循環良好才可以點起激光管,否則極易造成玻璃管的炸裂,此種事故不在保修范圍內。

    5另外,如果在激光管損壞前發現沒有通冷卻水,此時立即關閉電源,但不要通水,等待激光管自然冷卻至室溫,再開通冷卻水,開啟激光管檢查是否能夠正常使用。

    6如果冷卻水太臟,將嚴重影響激光器的正常使用,大幅縮短激光器的使用壽命。

    三、外圍設備及條件須知(詳見KY系列激光器使用手冊)

    1環境條件

    (1)環境溫度:1040

    (2)相對濕度:45%85%,不結露

    (3)氣壓:86106kpa

    (4)應該在防塵環境下使用此激光器

    (5)廠房必須要滿足當地關於激光設備運行的安全標準

    2電力條件

    單相電,電壓在200V240V之間,50Hz

    3冷卻系統條件

    (1)冷卻水溫度:1530℃,夏天最佳25℃,其它季節最佳20

    (2)冷卻水流速:≥6 L/min

    (3)水質量:飲用純凈水,雜質直徑小於0.2mm

    (4)pH值:6-9

    四、日常維護須知(詳見KY系列激光器使用手冊)

    1保持環境衛生,註意激光器出口鏡的維護;

    2定期更換冷水機/水泵的冷卻水,保證冷卻水的清潔;

    3隨時註意冷卻水水溫的變化,若使用水冷機最佳設置溫度夏季為25℃,其它季節最佳20℃;若使用水泵應控制溫度在30℃以下;

    4當環境溫度較低時,應確保冷卻水不結冰,必要時可以使用防凍液。

     

    Model:KY-45Sdetailed parameters

     

    Characteristics:

    Good mode. Suitable for marking craft gift, high precision engraving, and fine cutting.  

     

    Product picture

     

     

     

    Safety instruction(Refer toKY series laser instruction manualfor details)

    1 Optics safe instruction

    Laser radiation can cause great damage to eyes and skin. Don't directly expose eyes and skin in laser radiation.

    2 Power safe instruction

    Don’t approach or touch electric power source, both ends of laser, and the wires connected to the two ends when connect to the high voltage power.

    3 Other safe instruction

    (1) The laser is easy to ignite irradiated tinder, so don’t placed tinder and explosives within the radiation range and must prepare fire-fighting equipment in the workplace;

    (2) Cope with the harmful substance caused by processing materials when using the laser, and maintain draftiness.

    (3) The laser can only work in the presence of staff. If an exception occurs, please cut off the power immediately.

    (4) The laser is glass tube laser, and it is fragile. Please handle with care!

     

    Installation instruction(Refer to KY series laser instruction manual for details)

    1The middle outlet must be face up. The laser tube outlet should be connect to the cooling-water machine (water pump) inlet, and the laser tube inlet should be connect to the cooling water machine (water pump) outlet.

    2 Ensure the cooling water circulation is good before light the laser tube. Otherwise the laser can easily burst. Such accidents are not under warranty.

    3 If the laser is not connected to the cooling water when working before the laser is damage, you must turn off the power immediately. In this situation, don’t connect to the cooling water before the laser tube cooled to room temperature. Then light the laser tube, and check whether it is regular service.

    4 Dirty cooling water will seriously affect the normal use of the laser, and it can significantly cut down the laser life.

     

    Condition instruction(Refer to KY series laser instruction manual for details)

    1 Condition of circumstance

    (1)Environment temperature10—40

    (2)Relative humidity45%—85%, non-condensing.

    (3)Atmospheric pressure86—106kpa

    (4) Use the laser in the dust-proof environment.

    (5)The factory must meet the requirements of local safety standards on the running of the laser equipment.

    2 Condition of electricity

    Single-phase source, voltage:200V—240V50Hz

    3 Condition of cooling system

    (1) Cooling water temperature15—30. Summer optimal temperature is 25and other season is 20.

    (2)Cooling water flow rate≥6 L/min

    (3)Water qualityPurified water. Impurity diameter is less than 0.2mm

    (4)The pH of water6-9

     

    Routine maintenance instruction(Refer to KY series laser instruction manual for details)

    1 Maintain environmental health, and attention to the maintenance of the laser exit lens.

    2 replac the cooling water regularly, and ensure the cooling water is clean.

    3 Pay attentions to the change of cooling water temperature. If using cooling water machine, the summer optimal temperature is 25(other seasons is 20). If using water pump, the temperature should be controlled below 30.

    4 When the environment temperature is low, make sure the cooling water does not freeze. If necessary, use the antifreeze.

     



    新手教學
    供應單膜激光器/激光管/激光雕刻專業激光器/光斑細激光器_激光器_光電器件_電子元器件_貨源_批發一路發
    批發市場僅提供代購諮詢服務,商品內容為廠商自行維護,若有發現不實、不合適或不正確內容,再請告知我們,查實即會請廠商修改或立即下架,謝謝。
    相關商品
    line 線上客服  ID@tsq1489i
    線上客服