ng> 適用於各類磨床、超精機、精研、電腐蝕加工等設備，起到冷卻液凈化作用 ng> ng>二、特點 ng> ng> 1、主要部件用於隔磁材料，低噪音減速電機，鏈條轉動，運轉平穩，功率損耗ng> ng> 小，密封性能高，可延長使用壽命。ng> ng> 2、使冷卻液（切削液）保持清潔狀態，減少砂輪修整次數，提高工件精度，ng> ng> 可替代人工挖沙的耗時及冷卻液的消耗，有利於機床的精度和使用壽命。ng> ng> 3、本機型結構新穎，節能環保，便於安裝。可按機床或客戶要求來設計制造。ng> ng> 二、工作原理ng> ng> KD系列、由箱體、磁桶、膠輥減速電機等部件組成。冷卻液從入水口進入ng> ng> 箱體，分離通過磁桶將液體中的粉末性鐵屑吸附，雜質被吸，經過膠輥的碾ng> ng> 壓，擠乾，再由刮板將雜質鐵屑分離，清潔的液體從出水口流出，完成自動ng> ng> 分離的過程。ng> ng> 四、 安裝及註意事項ng> ng> 1、按銘牌標準設定流量裝配造型，進出水口若與機床不符，可加變徑接ng> ng> 頭變換。ng> ng> 2、 裝機前方向運轉正常的情況下方可放水，再適當調緊碟形螺母，使膠輥ng> ng> 與磁桶達到最佳的碾壓狀態。ng> ng> 3、長時間不工作時，應清理箱體以防雜質堆積凍結，鏈條間隙過大時應及ng> ng>時調整松緊，定期給鏈條上油。ng> ng> 4、雜質不能急劇增加，否則會使電機抱死及時處理膠輥和磁桶表麵的附著ng> ng> 物。ng> ng> 5、檢查維護前必須在斷電、斷水下進行。ng> ng> 五、 技術參數ng> ng> ng> ng>型號ng> | ng>功率ng> | ng>進水口ng> | ng>出水口ng> | ng>流量ng> | ng>Ang> | ng>Bng> | ng>Cng> | ng>A1ng> | ng>A2ng> | ng>A3ng> | ng>A4ng> | ng>KD-180ng> | ng>15Wng> | ng>47ng> | ng>50ng> | ng>25/minng> | ng>310ng> | ng>135ng> | ng>100ng> | ng>280ng> | ng>200ng> | ng>180ng> | ng>315ng> | ng>KD-180Qng> | ng>15Wng> | ng>47ng> | ng>50ng> | ng>25/minng> | ng>310ng> | ng>135ng> | ng>100ng> | ng>280ng> | ng>200ng> | ng>180ng> | ng>315ng> | ng>KD-300ng> | ng>25Wng> | ng>58ng> | ng>40*105ng> | ng>50/minng> | ng>310ng> | ng>135ng> | ng>100ng> | ng>390ng> | ng>320ng> | ng>300ng> | ng>315ng> | ng>KD-300Qng> | ng>25Wng> | ng>58ng> | ng>40*105ng> | ng>50/minng> | ng>310ng> | ng>135ng> | ng>100ng> | ng>390ng> | ng>320ng> | ng>300ng> | ng>315ng> | ng>KD-500ng> | ng>40Wng> | ng>100ng> | ng>40*105ng> | ng>100/minng> | ng>360ng> | ng>135ng> | ng>70ng> | ng>605ng> | ng>520ng> | ng>500ng> | ng>415ng> | ng>KD-500Qng> | ng>40Wng> | ng>100ng> | ng>40*105ng> | ng>100/minng> | ng>360ng> | ng>135ng> | ng>70ng> | ng>605ng> | ng>520ng> | ng>500ng> | ng>415ng> |
| 
