（一）Sealant appearance：封膠外形
(二)Product Guidelines:產品指南
產品型號（Product Model） | 發光顏色(Emitting Color) | 膠體顏色(Lens Appearance) |
SJ-SW3014 | 白色（White） | 黃色不透明(Yellow Disffuse) |
※Absolute maximum ratings at Ta=25℃ 最大絕對額定值
參數(Parameter) | 符號(Symbol) | 值(Value) | 單位(Unit) |
功率損耗(Power Dissipation) | Pd | 100 | mW |
正向電流(Continuous Forward Current) | IF | 30 | mA |
反向電壓(Reverse Voltage) | VR | 5 | V |
最大脈沖電流(Peak pulsing current) | IFP | 300 | mA |
工作溫度范圍(Operating Temperature Range) | Tops | -20℃ to+80℃ | |
儲存溫度范圍(Storage Temperature Range) | Tstg | -30℃ to+100℃ | |
抗靜電能力(Electrostatic Discharge) | ESD | 2000(HBM) | V |
NOTE:IFP Conditions:Pulse Width≦10msec, and Duty cycle≦1/10
IFP條件:脈沖持續時間≦10msec,占空比≦1/10
※Electrical-Optical Characteristics at Ta=25℃ 電性光電特性
參數（Parameter） | 符號(Symbol) | 最小值(Min) | 典型值(Typ) | 最大值(Max) | 單位(Unit) | Test Conditionc 測試條件 |
正向電壓(Forward Voltage) | VF | 3.0 | --- | 3.4 | V | IF=150mA |
發光強度(Luminous Intensity) | IV | / | / | / | / | / |
光通量(Luminous flux) | Φ | 12 | --- | 14 | lm | IF=150mA |
反向電流(Reverse Current | IR | / | / | 10 | μA | VR=5V |
冷白光(Cold White） Color Temperature | Tc | 7500 |
| 15000 | K | IF=150mA |
純白光(Pure white） Color Temperature | Tc | 5500 |
| 7000 | K | IF=150mA |
暖白光(Warm White） Color Temperature | Tc | 2600 |
| 3500 | K | IF=150mA |
發光角度(Viewing Angle) | 2θ1/2 | / | 120 | / | deg | IF=150mA |
NOTE:1.Tolerance of luminous intensity is ±15％
發光強度公差為±15％
2.Tolerance of forward voltage is ±0.1V
正向電壓公差±0.1V
(三)Product features:產品特性
◎發光效率高,光譜窄,單色性好
High luminous efficiency, spectral narrow, monochromaticity good
◎高顯色性高,顯示色彩逼真
High color rendering high, show vivid
◎低電壓直流驅動,功率低
Low voltage dc drive, power low
◎精密恒流,矽膠封裝,低衰減
Precision constant current, silica gel package, low attenuation
◎適用於所有表面貼裝技術組裝生產
Apply to all SMT technology assembly production
◎完全符合RoHS指令
Fully meet the RoHS instruction
(四)Packing:包裝方式
◎采用防靜電編帶包裝
The antistatic taping
◎數量:3000隻/盤
Quantity: 3000 only/tray
◎重量:143克/盤
Weight: 143 g/tray
(五)Product application:產品應用
◎戶外廣告牌,室內室外顯示屏,LED日光管,LED發光模組,軟硬燈條,背光源,LED燈飾,標準牌,光學指示,汽車內部照明,信號照明等
Billboard, indoor and outdoor display screen, LED solar tube, LED luminous module, soft hard light bars,
back light, LED lighting, standard CARDS, optical instructions, car interior lighting, signal lighting, etc
(六)Welding condition:焊接規范
◎材料焊接次數不超過2次.
Material welding times not more than 2 times.
◎焊接時請不要重壓LED燈。
During welding please don't weigh LED lamp.
◎焊接後溫度未回降到常溫時請勿扭曲線路板。
After welding temperature not back to normal temperature when do not distort circuit board.
◎手工焊接時，烙鐵溫度不高於300℃，每個焊腳焊接時間不超過3秒
Manual welding, the welding temperature is not higher than 300 ℃, each leg welding time not more than 3 seconds
(七)Storage standard:貯存規范
◎請在未準備使用LED之前不要打開防靜電袋子.
Please not ready before use LED do not open the anti-static bag.
◎LED在未開封之前應保存在30℃以下,濕度在60%以下的環境中,最長保存期為1年.
LED in the intact before should be kept in 30 ℃ below, humidity below 60% in the environment, the longest retention period for one year.
◎打開包裝待後,LED需保存在30℃/40%濕度以下的條件,且必須在7天內使用完.
Open the packing to stay, LED to save in 30 ℃ / 40% humidity the following conditions, and must be in 7 days after use.
◎如果LED超出瞭第3點要求,則LED必須經過烘烤才能使用,烘烤條件為:60±5℃,12個小時
If LED beyond the third point requirements, then LED must pass a baking to use, baking conditions for: 60 ± 5 ℃, 12 hours
(八)Important Notes:重點註意事項
◎我司顏色等級完全參照1931 CIE標準擬定。
We refer to the 1931 CIE that the Clor grading standards proposes.
◎發光強度公差為:±15％
The tolerance of luminous intensity is ±15％
◎正向電壓公差為:±0.1V
The tolerance of forward voltage is ±0.1V
◎客戶貯存及使用必須符合我司規格參數要求。
Customer storage and use must comply with our requirement.
◎LED光源無輻射,且不含重金屬等有害物質.
LED light source no radiation, and does not contain harmful material such as heavy metals.
◎LED光源得以正確使用方可保證其壽命,如果對LED使用有任何疑問可咨詢我司給予相關技術指導.
LED light source to the correct use of can ensure its life, if the LED use have any question can seek advice we give related technical guidance.
(九)Product shot:實物圖片
批發市場僅提供代購諮詢服務，商品內容為廠商自行維護，若有發現不實、不合適或不正確內容，再請告知我們，查實即會請廠商修改或立即下架，謝謝。
