ng>滾筒清洗機的工作原理：ng>間歇操作的滾筒式清洗機兩端加有擋板，周向開有帶蓋板的進出料口。料口向上時，可打開料口蓋板向裡加料；洗凈後，筒體轉至料口朝下，打開蓋板便可卸料。為便於物料在筒內翻 滾，加料不可太滿。一般這種清洗機采用噴水管連續或間歇地向筒內噴水以便使污物浸潤而迅速剝離和排走。連續式滾筒清洗機的滾筒兩端為開口式，原料從一端進入，另一端排出。物料在筒內的軸向運動，可以通過使筒傾斜安裝，也可通過在筒體內壁設置螺線導板或抄板的方式實現。為提高清洗效果，有的滾筒式清洗機內安裝瞭可上下、左右調節的毛刷。

The working principle of the drum washing machine drum type washing machine: both ends of intermittent operation with a baffle, Zhou Xiangkai has inlet and outlet with a cover plate mouth. Feed opening up, open the inlet cover plate to feed; after washing, the cylinder to the feeding mouth down, open the cover can discharge. In order to facilitate the materials in the barrel varus roll, feeding should not be too full. This washing machine adopts a spray pipe continuously or intermittently into the cylinder of water so that the dirt infiltration and rapid stripping and drain away. Both ends of the roller continuous roller cleaning machine is open, the raw material from one end to the other end, discharge. Axial movement of the material in the barrel, the barrel can be inclined installation, can also be achieved through the spiral guide or copy board is arranged on the inner wall of the barrel body way. In order to improve the cleaning effect, some drum type washing machine has been installed in the up and down, the hair brush.

ng>滾筒清洗機的應用：ng>物料由進料鬥進入落到滾筒內，隨滾筒的轉動而在滾筒內不斷翻滾相互摩擦，再加上噴淋水的沖洗，使物料表麵的污垢和泥砂脫落，由滾筒的篩網洞孔隨噴淋水經排水鬥排出。由進料口進入清洗槽內的原料，首先在兩個轉動刷輥產生的渦流中得以清洗，同時，由於兩個刷輥間隙較窄，故其間的水流有較高流速從而該壓力降低，被清洗物料在壓力差和刷輥摩擦作用下通過刷輥,進一步得到刷洗。而後，被清洗物料在出料翻鬥中又經高壓水得到進一步噴淋清洗。

Application of drum washing machine: material consists of feed hopper into into the drum, the drum rotation in the drum roll continuously mutual friction, coupled with the flushing spray water, so the material surface dirt and mud and sand falling holes, composed of a screen drum with spray water drainage hopper discharge. From the inlet into the cleaning groove of the raw materials, the first to be cleaned, the two rotating brush roll eddy current at the same time, because the two brush roller clearance is narrow, so the water has higher velocity and the pressure is reduced, cleaning materials through the brush roller brush roller pressure and friction effect further out. Then, by cleaning the material in the material bucket and the high pressure water further cleaning spray.

ng>滾筒清洗機的特性：ng>由給瓶端進入機器的瓶子，先後經過預沖洗、預浸泡、洗滌劑浸泡、洗滌劑噴射、熱水預噴、熱水噴射、溫水噴射和冷水噴射等清洗作用，最後從出瓶端離開洗瓶機。預沖洗是為瞭將瓶子外附著的污垢除去，以降低後麵洗滌液消耗量。洗液噴洗區位於洗液浸泡槽上方，這樣從瓶中瀝下的洗液又回到液洗槽。消毒後的空罐最後由第三個星形輪送到出罐軌道進入裝罐工序。空罐在清洗機中回轉時有一定的傾斜，因此可使罐內的水流出。污水由排水管排入下水道。

Characteristic of cylinder washing machine is composed of bottle machine: to end into the bottle, after pre washing, pre soaking, soaking, detergent, detergent spray hot water spray, water injection, water injection and water injection cleaning effect, leave the bottle washing machine and finally from the bottle end. Pre washing is to remove dirt attached to the bottle, in order to reduce the back washing fluid consumption. Lotion spray washing area is located above the soaking liquid from a bottle, so Li under the back washing bath lotion. Empty tank after disinfection finally by third star wheel to a tank track into the canning process. Empty cans in cleaning machine rotates a certain inclination, thus can make the tank water flows. The sewage from the drainage tube into the sewer.

新手教學

批發市場僅提供代購諮詢服務，商品內容為廠商自行維護，若有發現不實、不合適或不正確內容，再請告知我們，查實即會請廠商修改或立即下架，謝謝。