一． 用途：

A. Use:

可調高速勻漿機（均質器）是供科學研究單位，大專院校、醫藥、衛生防疫、輕工業、重工業、農業、環境衛生保護、森林保護等部門實驗室進行細碎、勻化、乳化、分散、強烈攪拌、潤溫、溶解有機物或無機物及樣品均質等作用。

Adjustable high-speed homogenate machine (homogenizer) is for scientific research units, colleges and universities, medicine, health and epidemic prevention, light industry, heavy industry, agriculture, environmental protection, forest protection and other departments for public health laboratories and finely, homogenization, emulsification, dispersion, strong stirring and temperature, dissolved organic matter or inorganic matter and homogeneous sample etc.

二． 結構及工作原理：

2. The structure and working principle:

該機選用200瓦2萬轉/分單相串激式微型電機，電機驅動旋刀在杯內作用，利用瓶內流體力學和高速機械剪切力作功。有大小六種瓶、刀、刀軸，並附有六個控溫杯，可根據物料的需要在杯內放入熱水或冷卻液進行調溫，並設有機械定位，整個機件作業自如方便，電器部分設有開關，通電指使燈，調速器可根據需要的轉速進行無級調速，外殼設有接地裝置，使用時安全可靠。

The machine chooses 200 watts 20000 RPM single-phase series type micro motor, motor driven rotary knife in the cup, use the bottle of fluid mechanics and high-speed mechanical shearing force. Size six kinds of bottles, knife, knife shaft, with six cups of temperature control, according to the needs of the material in the cup into hot water or coolant temperature, and is equipped with mechanical positioning, comfortable and convenient working the whole part electrical part is equipped with the switch, electricity charge lamp, speed can be stepless speed regulation according to the need of speed, the shell is equipped with grounding device, safe and reliable when used.

三． 技術數據：

3. Technical data:

1. 使用電源：220V ±10％;50HZ±5

1. The use of power: 220 v + / - 10%; 50 hz + / - 5

2. 最大消耗功率：200瓦

2. The maximum power consumption: 200 watts

3. 轉速：0-20000轉/分可自由選擇調節

3. Speed: 0-20000 - RPM can adjust the freedom to choose

4. 工作方法：連續

4. Working methods: continuous

5. 體積：500×370×350mm

5. Size: 500 * 370 * 350 mm

6. 重量：14千克

6. Weight: 14 kg

7. 負載量：

7. Load:

瓶 號

Bottles of no.

容量（毫升）

Capacity (ml)

瓶 號

Bottles of no.

容量（毫升）

Capacity (ml)

1

1

1-5

From 1 to 5

4

4

25-50

25 to 50

2

2

5-15

5-15

5

5

50-100

50-100.

3

3

15-25

15 to 25

6

6

100-150

100-100.

四． 使用須知：

4. Use the instructions:

1．按負載量選用瓶杯，將物料放入瓶內，把需用瓶杯順時針轉到定位器上，將電機軸居中，旋緊壓緊螺母，將電機軸與刀軸上的橡皮管連接，上下分佈均勻。開啟電源開關，指示燈亮即電源接通，調節調速器旋鈕，選擇合適的轉速。

Choose bottle cup 1. According to the load, the material into the bottle, turn need bottle cup clockwise to locator, center the motor shaft, and tighten gland nut, the rubber tube on the motor shaft with the knife shaft connection, and uniform distribution. Open the power switch, indicator is power on, adjust the speed knob, selec the appropriate speed.

2．開機前註意以下事項：

2. Before starting pay attention to the following items:

a. 電源必須於技術數據相符合。

A. the power must be in the technical data.

b. 用橡皮管將機軸與刀軸連接垂直。

B. the machine with rubber tube shaft connected to the knife axis vertical.

c. 為避免刀軸產生過量力矩，損壞機件，打碎瓶杯。調速器旋鈕應在零位上，方可開機，調速器由慢至快。

C. to avoid knife shaft of excessive torque, attaint parts, broken bottles of cup. Governor knob should be on the zero, to boot, the speed from slow to fast.

d. 刀片要經常修磨鋒利，對角角度要對稱，不能變形，保證開機穩定，高效率。

D. always grinding, sharp blade to symmetric diagonal Angle, not deformation, guarantee the stability of boot, high efficiency.

3．電機、調速器不能受潮，經常要保持清潔，妥善保管。

3. Motor, speed governor cannot be affected with damp be affected with damp, often to keep clean, safekeeping.

4．軸承要定期檢查，半年加耐高溫潤滑脂一次。

4. Bearing should be check regularly, and high temperature resistance grease once half a year.

5．發現不轉，調速器不調，指示燈仍亮著，要停機檢查。

5. Find don't turn, governor is not adjustable, lights were still on, check downtime.

6． 碳刷要經常檢查，磨損瞭要更新，發現碳刷火花過大應停止使用。檢查故障原因，修理好後，方可開機，以免整流子和線圈燒壞。

6. Carbon brush to regularly check, worn to update, found that too much carbon brush spark should stop to use. Check the cause of the problem, repaired before boot, lest the commutator and coil burn out.

更多與相關產品歡迎您來電咨詢 010-57462906

新手教學

批發市場僅提供代購諮詢服務，商品內容為廠商自行維護，若有發現不實、不合適或不正確內容，再請告知我們，查實即會請廠商修改或立即下架，謝謝。