產品簡介:

　AT6000呼出氣體酒精含量探測器是專用於測試人體呼出氣體中酒精含量的機器。本機敏感元件采用漢威電子先進的納米半導體酒精傳感器，具有極好的靈敏度和出色的重復性；測試程序由人工智能設計的微電腦控制，工作流程合理，簡潔便利，功能齊全，具有多種自適應能力；背光照明的LCD數位、字圖顯示，直觀清晰；小巧的便攜設計更便於您移動使用。當被測呼出氣體中的酒精含量超過預定值時，本機會自動發出聲音報警，為您的安全多一份提醒。

本產品設計、制造、檢驗遵守以下國傢標準：

GB/T21254-2007《呼出氣體酒精含量檢測機》
GB19522-2004《車輛駕駛人員血液、呼氣酒精含量閾值與檢驗》

特點:

◆ 先進的納米半導體酒精傳感器；
◆ 響應、恢復迅速、檢測快捷方便；
◆ SMD裝配工藝，性能穩定可靠；
◆ 人工智能微電腦控制；
◆ 測試過程屏幕直觀顯示；
◆ 藍色背光照明的LCD數位、字圖顯示；
◆ 便攜設計、小巧輕便；
◆ 酒精超限自動聲報警；
◆ 傳感器故障自檢；
◆ 智能節電設計，電池欠壓指示

主要技術參數:

Digital Indication:

2. Operation Instruction

2.1. Slide down the battery compartment on the back side, insert 3pcs AAA 1.5V batteries inside according to battery polarity indication and close it.

2.2. Press the switch button and last for 1s, the tester would be power on with a buzzer brief ringing, ‘Wait’ shows on down side of screen, meantime it shows 100 to 000 countdown, please wait now, otherwise its accuracy will be not good.

Until “Wait” disappears, tester will send out a ring,meantime shows “BLOW” and “C” gliding, now the test could begin.

Remarks: Its countdown speed will depend on concentration of last test, if concentration is high, it will be slow. If concentration is low, the countdown will be very quick.

2.3. Have a deep breath before testing, and blow directly to gas entry when “C”circularly shows, stop blow when heard its buzzer ring.

2.4. After blowing finished, the LCD screen willshow “ ” circularly, meantime shows “TEST”, this means the tester is analyzing the result, do not blow at this time. After analyze the screen will show the testing results.

It will turn off automatically after keep results for several seconds.

2.5. If a new testing needed, press the switch button again and repeat the above step 4.2～4.4.

3. Notification

3.1. Avoid any fall or strong shock.

3.2. If noise gas with high concentration existed,may the tester won’t work normally.

3.3. If testing is done under low voltage, certain error will be existed between the real value.

3.4. To ensure the testing result, please wait 15 mins to take the testing after your drinking.

3.5. The result may be unreliable for your first test if long time storage, please try second time.

3.6. Do not keep the tester in the environment of corrosive gas (Chlorine etc) for use or deposit, also in other bad surroundings.

3.7. Do not blow smoke to tester directly, especially the smokers.

3.8. When in consecutive testing, if blow immediately after drink, this concentration is very high, there will be some rudimental in mouthpiece. Please wait for at least 1 min to take second test, or, blow clean air for 3 seconds to clean out its mouthpiece.

3.9. After Long time use, there may be dirt on the tester, please use clean cloth to wipe off. Do not use any hard object or the solvent with any Corrosive ingredient.

Remarks: Common Fault and Solving solutions

To keep the continuous improvement of the products, we reserve the right to improve design without prior notice.

新手教學

批發市場僅提供代購諮詢服務，商品內容為廠商自行維護，若有發現不實、不合適或不正確內容，再請告知我們，查實即會請廠商修改或立即下架，謝謝。