尺寸規格

外徑： Φ63-500mm, 內孔徑 Φ25.4-50mm, 厚度： 1-5mm

表麵處理

本色，鍍鈦，滲氮，鍍鈦鋁

齒形分

有齒和無齒

有齒齒形

尖齒，圓弧齒，左右齒，高低齒。齒形及倒角型式根據加工材料。

材料

M2 及超高速鋼

用途

通用材料主要用於一般低硬度碳鋼及有色金屬棒材和管材的切斷。超硬材料及鍍鈦鋸片主要用於難切削材料（如不銹鋼）棒材管材的切斷。

常見問題

                  Problem

產生原因

             Possible Cauese

       解決方法

                      olution

            毛刺 Burr

齒節距太大

       Tooth pitch is too large

調整齒節距

        Adjusting teeth pitch

鋸齒已磨損

   Saw tooth are with abrasion

重新磨齒

          Gringing saw teeth

鋸齒間廢屑太多

Too much scraps produced between saw teeth

齒節距大小

        Tooth pitch is too small

調整齒節距

A        sjusting teeth pitch

錯誤的齒型

         Tooth form is too high

重新開齒

      Re-hobbing sawing speed

速度太快

     Sawing speed is too high

調整速度

       Adjusting sawing speed

鋸片爆裂

            Saw blade crached

切割速度太高

        Cutting speed is too high

調整切割速度

     Adjusting the cutting speed

進料速度太高

      Feeding speed is too high

調整進料速度

   Adjusting the cutting speed

鋸片進刀速度不穩定

          Feeding speed of the saw   blade Is not stable Enough   

調整鋸片進刀速度

          Adjusting the feeding speed of  The saw blade

進料和切割速度比錯誤

Incorrect tatio occurred between the feeding speed And cutting speed

調整速度比

Adusting the speed ratio

鋸片沒夾緊

Saw blade is nor firmly clanped

檢查法蘭

Checking the flange

加工材料沒夾緊

Work piece is not firmly clanped

檢查夾具

Checking the clanp

齒節距太小或太大

Tooth pitch is too large or too small

調整齒節距

Adjusting teeth pitch

潤滑或冷卻液沒有或不足

Ubricant or cooling oil is absent or insufficient

檢查機械

Checking the machine

管材焊縫不均

The tubing welded joint is uneven

更換管材

Replacement tubing

250*1.2

275*1.2

300*1.2

315*2.0

350*2.0

400*2.0

450*2.5

250*1.6

275*1.6

300*1.6

315*2.5

350*2.5

400*2.5

450*3.0

250*2.0

275*2.0

300*2.0

315*3.0

350*3.0

400*3.0

及小規格常

250*2.5

275*2.5

300*2.5

325*2.0

375*2.0

400*3.5

規鋸片銑刀

250*3.0

275*3.0

300*3.0

325*2.5

375*2.5

400*4.0

也有