SE-121
Product Description: System Outline
On this equipment, the work piece (Camshaft ) is supported on both centers, the work is rotated, and from the rotation angle and lift amount, cam profile measurement is performed.
A maximum number of 24 cams can be automatically measured.
Measurement data is procesed using a 32 bit CPU. Profile diagram, Speed diagram and Acceleration diagram can be printed out.
In addition, measurement data error in relation to the design standard value is calculated, and the error diagram can be output.
It can automatically measure up to a maximum of 24 cams, therefore it is possible to calculate the angle of the top points of each cam, or top lift amount,as well as each cam interval phase difference.
Also using Journal as the standard, deflection coorection etc. data pre-processing correction function is included, making it possible for high accuracy measurement Specification Outline
Power ………………AC100V 50/60Hz
Air Source ……………0.4MPa(4kg/cm2) or more compressed air
Measurement Method …………Optical Incremental EncoderOptical Incremental Linear scale
Measurement Resolution ………Angle Amount ：1 minute Lift Amount ：0.1μm
Applicable Type of Machines…８ types
Printing ………………A3 size laser printer
| | |
OD-100
Product Description: Measurement System Outline
On this machine, 400 pcs of work is set on the stocker, through the feed vacuum chuck, work is automatically fed to the measurement unit, and on the measurement unit, External Diameter is measured in comparism with master.
After measurement judgment, through the eject vacuum chuck, non-defective Products are arranged and stored. Defective Products are moved to a NG stocker.
The tolerance zone setting can be changed using a sheet key, measurement result can be printed out, and statisctics functions also exists making it very suitable for quality management of external diameter. Specification Outline
１) General Specification
?Power: AC100V 50/60Hz
?Air Source: More than 4kg/cm2
?Environment: 20 degrees±5 degrees Humidity Less than 85％
２) Data Specification
?End-Measuring Machine Resolution: 0.1μm
?Measurement Value Display: ±999μm
?No. of Passes: ６ digit counter
?No. of Defects : ６ digit counter
| | |
 |
SE-119
Product Description: System Outline
On this equipment, X, Y, Z Axis and rotation Axis ccordinates can be directly digital displayed, using the handy switch, standard position for each Axis can be set independently. (Zero set) can easily be performed, therefore measurement of complex shaped types of shaft can be performed with precision.
Especially, it exels in action on shaft groove lenght and width, or phase Measurement
Each Axis movement is performed by the operation panel handle and servo motor, therefor coarse motion and micro motion feeding is possible. Specification Outline
Power…AC100V
Measurement Method and Resolution
X, Y, Z Axis …………Optical Linear Scale
Resolution…0.2μm
Rotation Axis………Optical Rotary Encoder
Resolution…1 min.
Touch Probe………0.1mm stroke
Resolution…0.1μm
Center Height…………………150mm
Center Interval Distance ………………270mm
Stage Movement Quantity………………XAxis270mm
YAxis150mm
ZAxis150mm
| | |
 |
SE-112
Product Description: System Outline
This Measurement equipment is used for measuring large diameter roller shaped (profile) objects that exceed the work range of normal deflection measuring equipment.
By installing X Axis stage and θ Axis on the high accuracy surface plate, roller Squareness, deflection angle, cylindricity, crown etc measurement values can be analyzed from various perspectives using computer analysis.
In addtion, depending on the specification, OK-NG judgment, statistical processing, etc is possible. Specification Outline
Power: AC100V 50/60Hz
Measurement Item: Deflection Angle Squareness Cylindricity Crown
Center Interval: 2300mm
Center Height: 250mm
Use Center r : MTNo4
Surface Plate: JISSurface Plate Type
Surface Plate Straightness: ９μm
Ｘ Stage Stroke: 2000 Stroke
Ｘ Stage accuracy: ９μm
Sensor: １μm reading
| | |
 |
QB-102
Product Description: Measurement System Outline
Automatic Shape Measurement Equipment that supports various shaped works (Internal cam, shaft with groove, etc).
Due to computer control ，filler exchange, work automatic centering，edge Automatic detection and other processing can be performed. Also ，It has the capacity for managing large amounts of measurement data. By changing the software，measurement of various types of work shape is possible. Specification Outline
１) Power AC100V 1.5KW 50/60Hz
２) Rotation accuracy and Automatic centering accuracy Less than １μm
３) Angle Resolution ２ seconds and Angle accuracy less than 1 minute
4) Lift Amount Resolution 0.1μm，Stroke 10mm，accuracy Less than １μm
5) Data Output and printing of shape diagram，error diagram, etc is possible.
| | |
 SE-100
Product Description: Measurement System Outline
Work deflection measurement and work surface condition is enlarged and displayed on the screen.
Accordingly, scratched and other dents that cannot be visually detected becomes visible. Specification Outline
１)Magnification ：200 Times
２)Center Interval ：1000，1500，2000，3000mm
| | |
 QA-100
Product Description: Measurement System Outline
Automatic Inspection Equipment forappearance inspection using image processing technology.
High speed processing is possible and so it can be used for inline process inspection.
Helps to reduce the number of personnel doing visual inspection. Specification Outline
１) AC100V less than 10A
２) Inspection Time 2.5 seconds ／１ pc…Including Judgment Output
３) Resolution 512×480 pixels
4) Supports multiple types of IC cards.
| | |
 |
OA-108
Product Description: Measurement System Outline
On this equipment, small diameter roller (For Example, video guide roller )Lenght or unevenness can be measured with high accuracy, pass-fail judgment in relation to measurement standard is performed, and sorted.
The work is inserted into a hopper, by pressing the start switch only, automatic measurement, sorting and work eject is performed.
2 stage roller (Resin inner type) dislodgment force judgment is also possible. Specification Outline
１) General Specifications
?Power AC100V 50/60Hz 500VA
?Air Source 4?/cm2 or more compressed air
?Use Environment Normal Measurement Environment
２) Cycle Time
?６ seconds ／pc
３) Accuracy
?Repetition Accuracy ２μm
4) Pass-fail judgment Setting Unit
?Minimum Unit 1μm
5) Display
?Calculation Result Display ，Minimum Unit １μm
６) Data Output
?RS232C Compliance
７) Can display No of Good Products and No. of defective Products(In Totla or per item).
| | |
 |
QB-101
Product Description: Measurement System Outline
On the cylindrical work edge surface, the cylindircal center standard is divided equally (２ - 12 portions)and the processed minute width groove shape or machining data data is measured.
Because the actual work groove width 0.8 - 2.0mm is very small, measurement that is not possible with general purpose 3 dimensional measuring equipment is performed automatically and accurately using special precision positioning stage and 32 bit computer. Also using sensing mechanism and special feeler and ２ pcs of 0.1μm resolution sensors, due to automatic correction computing, high precision measurement that reduces feeler deflection and error is performed and the measurement accuracy guarranteed. Specification Outline
１）General Specifications
?Power AC100V±５％，50/60Hz，200VA
?Air Source ５kg/cm2 - 9kg/cm2 Clean air
?Use Environment Room Temperature：20℃±５℃ Humidity：80％RH and below
２）Accuracy Warranty
?Groove Width………±１μm and below
?Groove Width Parallellism……１μm and below
?Groove Width Squareness……１μm and below
?Groove Partition Angle……±30 Angle seconds
?Groove Inclination Angle……±１ degre
?Shape diagram……（Lateral Magnification×20，×50 selecion）
（Vertical Magnification×200，×500 selection）
（Inclination Angle Correction Enable/Disable Selection）
| | |
 |
OK-111
Product Description: System Outline
All processes on this equipment are completely automated from work ejection, measurement, judgment, sorting, to non defective product storage
1 hour of unattended operation is possible.
For measurement, a 0.1μm resolution non contact detector is adopted with repetition accuracy of 1μm making it possible for high precision measurement.
Also measurement data is processed using a 32 bit CPU, cycle time per piece is only 3.5 seconds.
Data can be saved in a file. It can be used for process capacity statistics management and can also be printed out. Specification Outline
| | Power……………… | AC100V 50/60Hz about 1.5KVA | | Air Supply…………… | 0.4MPa（4kg/cm2） or more compressed air | | Measurement Item………… | Lenght Measurement ( L )
Squareness Measurement
Parallellism Measurement
Thickness Measurement ( ｔ )
Thickness Parallellism | | Repetition Accuracy…… | １μm | | Cycle Time…… | 3.5 seconds (Including stocker automatic exchange time ) | | Unattended Operation Time…… | 1 Hour | | Work change ……… | 3 Types | | Work Measurement ……… | Thickness Measurement 3～4.5mm
Lenght Measurement 20～42mm
Width Measurement 15～25mm |
| Measurement Item  |
|
 SA-162
Product Description: System Outline
This Equipment with a worm gear attached, is rotated and gear accuracy can be measured under a dynamic condition.
Variation in center interval distance, deflection element and gear abnormality can be judged.
A 0.5μm resolution detector is adopted, making it possible for , high precision measurement.
The data is processed on a computer, and data diagram is displayed on the screen.
As an option, marking of maximum point and rank classification functions can be addes. Specification Outline
Power…………………AC200V 50／60Hz 1.5KVA
Air Source………………0.4MPa（４Kg/cm2）o r more compressed air
Repetition Accuracy………２μm
Cycle Time……30 seconds
Applicable Type of Machines…15 types
Option…………Marking Function, Rank Separation Function, Barcode Reader
| | |
 |
QB-108
Product Description: System Outline
On the standard specification of this equipment, in addition to the representative flat gear, spiral gear, internal gear, and bevel gear inspection is possible. (Optionally hypoid gear is also possible)
acoustic testing, tooth contact testing, both teeth surface mating testing, inspection items are also possible.
Also, for high accuracy measurement, we are using granite material for the measurement base. Specification Outline
Power …………………AC200V １KVA
Load Break ………can be set to any load using a dial.
Target Work …………MAX diameterφ250mm
MAX weight 10kg (including jigs)
Axis Interval Distance ……………Parallel Axis ：－5 - 255mm
Intersecting Axis, Drive side ：127.5 - 290mm Passive side：０ - 127.5mm
Axis Angle ………………０ - 360゜, Can be set to any position. (30 seconds Unit set)
No. of Revolutions………………０ - 2500rpm Nonstep Setting: Normal/Reverse Possible
Required floor space …………1700(Ｗ)×900(Ｄ)mm
※This equipment is developed and marketed under technical agreement with Nagaoka Gear Works Co Ltd.
| | |
 |
|
|
|
|
|  |
